|
1.
|
|
2.
|
|
3.
|
|
4.
|
|
•
|
First Name (*) - This is the first name of the provisioned subscriber.
|
|
•
|
Last Name (*) - This is the last name of the provisioned subscriber.
|
|
•
|
Site Name (*) - This is the Site Name (as defined in the 'Site' tab) which the provisioned subscriber belongs to.
|
|
•
|
Extension - The Extension number should be in the range entered in the "Extension Range" field in either the Endpoints or Site tabs.
|
|
•
|
Subscriber Dialing Permissions (*) - Important Note: This field is only mandatory for RA deployments in case the respective subscriber is assigned a CDC predefined Feature Profile! More specifically, in this case it is the responsibility of the user to configure Dialing Permissions for this subscriber according to his assigned Feature Profile.
|
|
•
|
Directory Number (*) - This is mandatory field. Either the E.164 numbers can be entered which are in the range given on the Endpoint tab or Fully Qualified Private numbers can be entered which are in the range given on the Site tab.
|
|
•
|
External Caller ID - This column represents the calling DN sent out when a call is made from a subscriber. Generally this is used to represent an Attendant in the office which takes the calls and transfers the calls to the appropriate person in the office.
When the External Caller ID is left empty the value is taken the same as the Direct Inward Dialing Number. |
|
•
|
|
•
|
Analog Adapter Port - Optional field which defines the port number for the subscriber DN on a ATA. Port numbering starts from port 1.
|
|
•
|
Analog Adapter Fax (T.38) - Optional field which enables FXS interface T.38 fax negotiation for the subscriber DN on an ATA.
|
|
•
|
MLHG Group - Subscribers belonging to the same Hunt Group (MLHG) must have the same Group ID entered. A subscriber can be part of multiple hunt groups, therefore, this can be a comma separated list. A comma separated list may be used here. The pilot can be also be DID.
|
|
•
|
MLHG Type (only set for pilot number) - Hunting algorithm for the MLHG. Is assigned to the pilot number of the MLHG. Required for the pilot number of the hunt group.
|
|
–
|
|
–
|
|
–
|
|
–
|
|
•
|
Pickup Group - Assigned number of the pickup group. Start with 1 and increment by one for each new pickup group. Insert the same number for all the devices in the same pickup group. (must be a decimal number less than 10,000).
|
|
•
|
Openscape Mobile Feature - Enable/disable OpenScape Mobile Feature. Default value is 'no'.
|
|
•
|
Circuit User - If enabled the subscriber will be configured as a Circuit user connected via ATC. Default value is 'no'.
|
|
•
|
Phone PIN - Not yet used.
|
|
•
|
Voicemail - This field is used to overwrite the 'Default Voice Mail Assignment' in the General Tab. If the field is left empty then the value from 'Default Voice Mail Assignment' will be used.
|
|
•
|
Faxmail - Default value for Xpressions FaxMail is “No”.If Faxmail is set to “Yes” while Voicemail is set to “No”, then email address should be provided and following should be set:
|
|
•
|
Remote Subscriber - Set it to 'yes' for subscribers behind a central-SBC.
|
|
•
|
Mobility - Not yet used.
|
|
•
|
Feature Profile - Needed only if the customer has defined Feature Profiles.
|
|
•
|
DLS Profile - By filling up this field you may override the DLS Profile that is automatically assigned by CDC. The user should make sure that the specified DLS profile is accurate.
|
|
•
|
Keyset Use - Enabled only for devices that support keysets. Default is no keyset use. The following non default values are supported:
|
|
–
|
|
–
|
|
•
|
Line Key Label Digits - This is the number of digits of a Line Appearance DN at Primary Line's Phone Display Note: If the field is left empty then WebCDC autofills it using the number of digits of the Primary Line's Extension
|
|
•
|
Line Keys Order - This is the Keys' Assignment order in Primary Line's Key Layout:
|
|
•
|
Keyset Module - This is the sidecar module option and this can only be assigned to Openstage and OpenScape Desk Phone devices. The default option is no.
|
|
•
|
Keyset Line 1...9 - The assigned number.
|
|
•
|
Keyset Module - Keyset Module: This is the sidecar module option and this can only be assigned at Openstage 15/40/60/80
|
|
•
|
Module Line Keys Order - Module Line Keys Order: This is the Keys' Assignment order in Primary Line's Module Key Layout.
|
|
•
|
Keyset Line 1...18 - The assigned number.
NOTE: When editing by clicking the Hide Keyset Columns / Show Keyset Columns button the previous 6 fields can be hidden or shown. |
|
•
|
Prompt Language - The language that is used in the announcements played to the subscriber by the Media Server.
|
|
•
|
Device Display Language - Language used on the OpenStage phone.
|
|
•
|
Windows Login ID - The configuration data is stored in the Windows roaming profile of the user. This enables the user to access their configuration data through any computer in the network.Furthermore, it is mandatory for all UC Users in order to utilize the SSO functionality.
|
|
•
|
Email - It is used in the Xpressions user configuration file as well as a possible option for the UC Instant messaging address on UC tab.
|
|
•
|
UC User - Yes / No
|
|
•
|
First Speed Dial List - The subscriber’s primary speed dial list. If left blank, then the site’s primary default list (see Site) is used.
|
|
•
|
Second Speed Dial List - The subscriber’s secondary speed dial list. If left blank, then the site’s secondary default list (see Site) is used.
|
|
•
|
Digest Password - Password used for digest authentication of the subscriber
|
|
•
|
Business Authorization Code - Authorization code for business calls.
Authorization codes have to be unique within a business group. |
|
•
|
Private Authorization Code - Authorization code for private calls.
Authorization codes have to be unique within a business group. |